Design and analysis of the separating device for peanut half-feed combined harvesting

Dongjie Li, Jalin Hou, Dongwei Wang, Zenghui Gao, Zengcun Chang

Abstract


During combined peanut harvesting operations, the separating device plays a crucial role in determining peanuts’ damage rate and impurity content. In order to enhance the quality and efficiency of peanut harvesting, this study investigates the separating device of a two-ridge and four-row half-feeder combine harvester. Firstly, the operating principle of the separating device was analyzed, and a combined air-and-screen separating device was selected. Secondly, based on the movement state of peanut pod impurities in different sections of the separating device surface, the theoretical analysis of peanut pod impurity movement was carried out, and the peanut pod impurity dynamics model was constructed. At the same time, CFD software was used to analyze the airflow field inside the separating device. Moreover, the test factors affecting the separating effect were explored: fan wind speed, separating device surface inclination, and vibration frequency. The optimal working parameters of the device were determined as follows: a fan wind speed of 8.9 m/s, a separating device surface inclination angle of 8.3° concerning the horizontal, and a separating device vibration frequency of 7.2 Hz. The impurity content rate of the peanut pods was 1.48%, and the damage rate of the separating device was 1.61%. Finally, the impurity content of peanuts in the validation experiment was 1.53%, and the peanut damage rate was 1.68%. The effectiveness of the separating device operation was verified through field tests. The potential for further research on peanut harvesters is highlighted based on the findings of this study.
Keywords: combine harvester, air-and-screen separating device, peanut, impurity content ratio, damage rate
DOI: 10.25165/j.ijabe.20251801.8711

Citation: Li D J, Hou J, Wang D W, Gao Z H, Chang Z C. Design and analysis of the separating device for peanut half-feed combined harvesting. Int J Agric & Biol Eng, 2025; 18(1): 92–100.

Keywords


combine harvester, air-and-screen separating device, peanut, impurity content ratio, damage rate

Full Text:

PDF

References


Guan M. Research on full-feeding peanut picking test device and key components of peanut picker. PhD dissertation. Shengyang: Shengyang Agricultural University, 2017; 135p. (in Chinese)

Zheng Y L. Experimental study on the air suction fresh peanut cleaning and removing device. Master dissertation. Shengyang: Shengyang Agricultural University, 2020; 67p. (in Chinese)

Wang B, Hu Z C, Peng B L, Zhang Y H, Gu F W, Shi L L, et al. Structure operation parameter optimization for elastic steel pole oscillating screen of semi-feeding four rows peanut combine harvester. Transactions of the CSAE, 2017; 33(21): 20–28. (in Chinese).

Gao L X, Chen Z Y, Charles C, Butts C L. Development course of peanut harvest mechanization technology of the United States and enlightenment to China. Transactions of the CSAE, 2017; 33(12): 1–9.

Wang Y F. Design of the cleaning device for the peanut combine harvester and performance studies. Master dissertation. Qinhuangdao: Hebei Normal University of Science & Technology, 2022; 95p.(in Chinese)

Wang D W, Shang S Q, Li X, Gao D X. Type L cleaning separation mechanism of peanut combine harvester. Transactions of the CSAM, 2013; 44(Supp.2): 68–74, 51. (in Chinese)

Xu P Q, Dai F, Zhao W Y, Shi R J, Song X F, Qu J F. Simulation analysis and experiment of operation process of flax threshing and cleaning device. Transactions of the CSAM, 2023; 54(S1): 161–171. (in Chinese)

Zhang D M. Study on working mechanism and experimental research of cleaning device for millet. PhD dissertation. Heilongjiang: Heilongjiang Bayi Agricultural University, 2023; 186p. (in Chinese)

Kluge W. Neuzeitliche siebmaschinen fur die aufbereitung. Erdol and Kohle, 1975; 4: 705–711.

Zhang N. Research on working mechanism and optimization analysis of chaffer sieve cleaning device in corn grain harvester. PhD dissertation. Changchun: Jilin University, 2023; 156p. (in Chinese)

Dai F, Zhao W Y, Song X F, Shi R J, Liu G C, Wei B. Parameters optimization and experiment on separating and cleaning machine for flax threshing material. Transactions of the CSAM, 2020; 51(7): 100–108. (in Chinese)

Wang S S, Lu M Q, Hu J P, Chen P, Ji J T, Wang F M. Design and experiment of Chinese cabbage seed threshing device combined with elastic short-rasp-bar tooth. Transactions of the CSAM, 2021; 52(11): 86–94. (in Chinese)

Wan X Y, Yuan J C, Yang J, Liao Y T, Liao Q X. Effects of working parameters on the performance of cyclone separator for rapeseed combine harvester based on CFD. Int J Agric & Biol Eng, 2023; 16(1): 128–135.

Tang H, Xu C S, Zhao J L, Wang Y J. Screening and impurity removal device to improve the accuracy of moisture content detection device for rice. Int J Agric & Biol Eng, 2022; 15(6): 113–123.

Yang M, Zhang Y H, Zhang C, Gu F W, Yu Z Y, Hu Z C. Design and experiment of fan-sieve combined peanut film seedling separating device based on shredding and separating. Transactions of the CSAM, 2020; 51(12): 112–121. (in Chinese)

Li X Y, Du Y F, Mao E R, Zhang Y, Liu L, Guo D F. Design and experiment of corn low damage threshing device based on DEM. Int J Agric & Biol Eng, 2023; 16(3): 55–63.

Zhou L. Design and testing of a floor-standing jujube picking-conveyor cleaning device. Master dissertation. Shihezi: Shihezi University, 2020; 80p. (in Chinese)

Li H C, Li Y M, Tang Z, Xu L Z, Zhao Z. Numerical simulation and analysis of vibration screening based on EDEM. Transactions of the CSAE, 2011; 27(5): 117–121. (in Chinese)

Wu D L, Ding D, Cui B W, Jiang S, Zhao E L, Liu Y Y, et al. Design and experiment of vibration plate type camellia fruit picking machine. Int J Agric & Biol Eng, 2022; 15(4): 130–138.

Feng Y L, Yin X C, Jin H R, Tong W Y, Ning X F. Design and experiment of a Chinese chive harvester. Int J Agric & Biol Eng, 2023; 16(2): 125–131.

Du X, Jiang F, Li S, Xu N, Li D W, Wu C. Design and experiment of vibratory harvesting mechanism for Chinese hickory nuts based on orthogonal eccentric masses. Computers and Electronics in Agriculture, 2019; 156: 178–186.

Wang B, Hu Z C, Wu N, Zhang Y H. Desing and experiments of 4HZB-2A peanut picker. Chinese Agricultural Mechanization, 2012; 1: 111–114. (in Chinese)

Chen Z Y, Gao L X, Chen C, Butts C L. Analysis on technology status and development of peanut harvest mechanization of China and the United States. Transactions of the CSAM, 2017; 48 (04): 1–21. (in Chinese)

Hou J L, Wang H X, Niu Z R, Tang R, Li T H. Discrete element simulation and experiment of picking and clearing performance of garlic seed-picking device. Transactions of the CSAE, 2019; 35(24): 48–57. (in Chinese)

Zhang P, Xu H B, Hu Z C, Chen Y Q, Cao M Z, Yu Z Y, et al. Characteristics of agricultural dust emissions from harvesting operations: Case study of a whole-feed peanut combine. Agriculture, 2021; 11: 1068.

Li D J, Shang S Q, He X N, Zhao Z, Chang Z C, Wang Y T, et al. Experiments and analysis of a peanut semi-feeding picking mechanism based on the JKR model. Agriculture, 2022; 12: 1418.

Yan J C, Xie H X, Wei H, Wu H C, You Z Y. Optimizing the drying parameters of a fixed bed with reversing ventilation for peanut using computer simulation. Int J Agric & Biol Eng, 2021; 14(5): 255–266.

Wang Z B, Wang Z W, Zhang Y P, Yan W X, Chi Y J, Liu C Q. Design and test of longitudinal axial flexible hammer-calw corn thresher. Transaction of CASM, 2020; 51(S2): 109–117. (in Chinese)




Copyright (c) 2025 International Journal of Agricultural and Biological Engineering

Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 International License.

2023-2026 Copyright IJABE Editing and Publishing Office