Investigation of the pin-roller metering device and tube effect for wheat seeds and granular fertilizers based on DEM

Sugirbay Adilet, Kaiyuan Zhao, Guangyao Liu, Nukeshev Sayakhat, Chen Jun, GuangRui Hu, Lingxin Bu, Yu Chen, Hongling Jin, Shuo Zhang, Zagainov Nikolay, Muratkhan Marat

Abstract


The metering device is the central part of the seeder discharging granular fertilizers or seeds from the hopper to the colter passing through the tube. Depending on the metering device design, the batches of particles are discharged or discharged evenly. This research analyzes existing metering devices, and a new pin-roller metering device is recommended to discharge evenly high doses of granular fertilizers and wheat seeds at low rotation speeds. The objective was to adapt the metering device to precision agriculture so that a little electric motor containing gearbox drives every metering device. Therefore, the pin-roller metering device parameters were investigated to apply high doses of granular fertilizers and wheat seeds evenly. The optimal pin positions were determined according to response surface methods (RSM) by simulating the granular fertilizers and wheat seeds' behavior on DEM. The coefficient of variation (CV) and the slip rate (SR) of the particles between the pins were chosen as indicators for evaluating the pin-roller. The shape of the pin was specified, and then the number of lines, the number of pins in a line, and the pin height were chosen to optimize. The analysis of the simulation results shows the optimal parameters: the number of pins in a line is four, and the number of lines is sixteen. The SR of granular fertilizers and wheat seeds were 8% and 2%, respectively. The pin-roller metering device is compared with the six-grooved and twelve-grooved metering devices. The comparison results show that the pin-roller metering device distributes twice more uniformly than other metering devices. The CV of the granular fertilizer distribution for six-grooved, twelve-grooved, and pin-roller metering devices was 111.13%, 80.74%, and 37%, respectively. The CV of the wheat seed distribution for twelve-grooved and pin-roller metering devices was 96%, and 37%, respectively. As long as the particles interact with the tube, leaving the metering device, the effect of tube type and position is investigated. As a result, it was determined that the tube has minimal effect on the pin-roller metering device while positively impacting the six-grooved and twelve-grooved metering devices, improving the CV of the particle distribution into the soil.
Keywords: pin-roller, metering device, DEM, coefficient of variation, slippage rate, tube
DOI: 10.25165/j.ijabe.20231602.7721

Citation: Adilet S, Zhao K Y, Liu G Y, Sayakhat N, Chen J, Hu G R, et al. Investigation of the pin-roller metering device and tube effect for wheat seeds and granular fertilizers based on DEM. Int J Agric & Biol Eng, 2023; 16(2): 103－114.

Keywords


pin-roller, metering device, DEM, coefficient of variation, slippage rate, tube

Full Text:

PDF

References


Cisternas I, Velásquez I, Caro A, Rodríguez A. Systematic literature review of implementations of precision agriculture. Computers and Electronics in Agriculture, 2020; 176: 105626. doi: 10.1016/j.compag.2020.105626.

Dobermann A, Blackmore S, Cook S E, Adamchuk V I. Precision farming: challenges and future directions. in Proceedings of the 4th International Crop Science Congress. Brisbane, Australia, 2004; Oct. 26：217p.

Sandoval J, Eugenio R, Cruz I, Canteñs G. Mechatronic system for the control of fertilizer and pesticide granules dispensers of a fertilizer seeder. RevistaMexicana deCiencias Agrícolas, 2018; 21: 4355-4369.

Yu H F, Ding Y Q, Liu H T, Zhu W Q, Liu G Q, Fu X Q, et al. Optimization design and application of variable rate fertilization system for small-scaled fields. Transactions of the CSAE, 2018; 34(3): 35-41. (in Chinese)

Yu H F, Ding Y Q, Fu X Q, Liu H T, Jin M F, Yang C L, et al. A solid fertilizer and seed application rate measuring system for a seed-fertilizer drill machine. Computers and Electronics in Agriculture, 2019; 162: 836-844.

Cancan S, Zhou Z Y, Zang Y, Zhao L Q, Yang W W, Luo X W, et al. Variable-rate control system for UAV-based granular fertilizer spreader. Computers and Electronics in Agriculture, 2020; 180: 105832. doi: 10.1016/j.compag.2020.105832.

Song C C, Zhou Z Y, Jiang R, Luo X W, He X G, Ming R. Design and parameter optimization of pneumatic rice sowing device for unmanned aerial vehicle. Transactions of the CSAE, 2018; 34(6): 80-88. (in Chinese)

Su D X, Yao W X, Fenghua Y, Liu Y H, Zheng Z Y, Wang Y L, et al. Single-neuron PID UAV variable fertilizer application control system based on a weighted coefficient learning correction. Agriculture, 2022; 12(7): 1-22.

Li L, Qian L, Yan-yan C. Half-precision self-walking variable fertilization seeder design. International Journal of Hybrid Information Technology, 2016; 9(6): 177-188.

Yang S, Wang X, Zhai C Y, Dou H J, Gao Y Y, Zhao C J. Design and test on variable rate fertilization system supporting seeding and fertilizing monitoring. Transactions of the CSAM, 2018; 49(10): 145-153. (in Chinese)

Nukeshev S, Eskhozhin K, Eskhozhin D, Syzdykov D. Justification of design and parameters of seeding unit for fertilizers. Journal of the Brazilian Society of Mechanical Sciences and Engineering, 2017; 39(4): 1139-1149.

Brown E. Sowing seeds for the agricultural revolution: Jethro Tull (1674-1741). Tractor, 2003.

Jin, M F, Ding Y Q, Yu H F, Liu H T, Jiang Y Z, Fu X Q. Optimal structure design and performance tests of seed metering device with fluted rollers for precision wheat seeding machine. IFAC Papersonline, 2018; 51(17): 509-514.

Beaujot N, Vennard G, Markham N. Air seeder tank and distribution apparatus. Seedmaster Manufacturing Ltd, 2017.

Ess D R, Hawkins S E, Young J C, Christmas E P. Evaluation of the performance of a belt metering system for soybeans planted with a grain drill. Applied Engineering in Agriculture, 2005; 21(6): 965-969.

Tishkov N M, Makhonin V L, Nosov V V. Soybean seed yield and yield quality depending on the fertilizers doses and application methods. Oil Crops, 2019. 180: p. 53-60.

Gao J, Zhang J X, Zhang F, Hou Z Y, Zhai Y H, Ge L Z. Analysis of movement law and influencing factors of hill-drop fertilizer based on SPH algorithm. Applied Sciences, 2020; 10(9): 1643-1653.

Beard T, Maaz T, Borrelli K, Harsh J, Pan W. Nitrogen affects wheat and canola silica accumulation, soil silica forms, and crusting. Journal of Environmental Quality, 2018; 47(6): 1380-1388.

Gollany H T, Allmaras R R, Copeland S M, Albrecht S L, Douglas C L. Tillage and nitrogen fertilizer influence on carbon and soluble silica relations in a Pacific Northwest mollisol. Soil Science Society of America Journal, 2005; 69(4): 1102-1109.

Wiggenhauser M, Bigalke M, Imseng M, Keller A, Rehkamper M, Wilcke W. Using isotopes to trace freshly applied cadmium through mineral phosphorus fertilization in soil-fertilizer-plant systems. Science of the Total Environment, 2019; 648: 779-786.

Colaco A F, Molin J P. Variable rate fertilization in citrus: a long term study. Precision Agriculture, 2017;18(2): 169-191.

Li X Z, Hao M D, Zhao J, Wang Z, Fu W, Liu Z Z. Effect of long-term fertilization on wheat yield under different precipitation patterns. Chinese Journal of Applied Ecology, 2018; 29(10): 3237-3244.

Antonangelo J A, Firmano R, Alleoni L, Oliveira A, Zhang H L. Soybean production under continuous potassium fertilization in a long-term no-till oxisol. Agronomy Journal, 2019; 111(5): 2462-2472.

Nukeshev S, Eskhozhin K, Karaivanov D, Sankibaev T, Kakabayev N. Theoretical and experimental substantiation of the design of an opener for intrasoil broadcast sowing of grain crops. Bulgarian Journal of Agricultural Science, 2016; 22(5): 862-868.

Gurjar B, Sahoo P K, Kumar A. Design and development of variable rate metering system for fertilizer application. Journal of Agricultural Engineering Research, 2018; 54(3): 12-21.

Nukeshev S, Yeskhozhin K, Tokusheva M, Zhazykbayeva Z. Substantiation of the parameters of the central distributor for mineral fertilizers. International Journal of Environmental and Science Education, 2016; 11: 7932-7945.

Kara M, Bayhan A K, Ozsert I, Yildirim Y. Performance of fluted roll metering devices in seed drills with ammonium sulphate and diammonium phosphate. Applied Engineering in Agriculture, 2010; 26(2): 197-201.

Nukeshev S, Sugirbay A. Fertilizer metering apparatus. Eurasian Scientific Association, 2015; 1: 24-27. (in Russian)

Lv H, Yu J Q, Fu H. Simulation of the operation of a fertilizer spreader based on an outer groove wheel using a discrete element method. Mathematical and Computer Modelling, 2013; 58(3-4): 836-845.

Ding S P, Bai L, Yao Y X, Yue B, Fu Z L, Zheng Z Q. Discrete element modelling (DEM) of fertilizer dual-banding with adjustable rates. Computers and Electronics in Agriculture, 2018; 152: 32-39.

Lv H, Yu J Q, Fu H. Simulation of the operation of a fertilizer spreader based on an outer groove wheel using a discrete element method. Mathematical and Computer Modelling, 2013; 58(3-4): 836-845.

Zeng S, Tan Y P, Wang Y, Luo X W, Yao L M, Huang D P, et al. Structural design and parameter determination for fluted-roller fertilizer applicator. Int J Agric & Biol Eng, 2020; 13(2): 101–110.

Feng H M, Gao N N, Li Y, Fu W Q, Guo Y M. Control method for parameters cordinate match of fluted roller fertilizer apparatus. INMATEH Agricultural Engineering, 2020; 60(1): 211-220.

Eskhozhin D, Nukeshev S, Zhalsylykova Z, Eskhozhin K, Balabekova A. Design and study of a dispenser for the introduction of the main batch of mineral fertilizers. Mechanika, 2018; 24(3): 343-351.

Zhaksylykova Z, Eskozhin D, Nukeshev S, Akhmetov Y, Yeskhozhin K. Design of the construction and parameters justification of stud-belt seeding machine for application of the main dose of mineral fertilizer. International Journal of Environmental and Science Education, 2016; 11: 12959-12972.

Maleki M R, Jafari J F, Raufat M H, Mouazen A M, De B J. Evaluation of seed distribution uniformity of a multi-flight auger as a grain drill metering device. Biosystems Engineering, 2006; 94(4): 535-543.

Zhang L P, Zhang L X, Zheng W Q. Fertilizer feeding mechanism and experimental study of a spiral grooved-wheel fertilizer feeder. Journal of Engineering Science and Technology Review, 2018; 11(2): 107-115.

Ovtov V A, Polikanov A V, Orekhov A A, Shumaev V V, Gudin V M. Theoretical studies of geometric and kinematic parameters of a roller transporting device. Нива Поволжья, 2020; 1(54): 13-17.

Nukeshev S O, Romanyuk N N, Yeskhozhin K J, Zhunusova A E. Methods and results of the research of the fertilizer distributor of cutter-ridger-fertilizer. Herald of Science of S.Seifullin Kazakh Agro Technical University, 2016; 3(90): 138-145.

Boydas M G, Turgu N. Effect of vibration, roller design, and seed rates on the seed flow evenness of a studded feed roller. Applied Engineering in Agriculture, 2007; 23(4): 413-418.

Svensson J E T. Effects of constructional and operational variables on the mean mass-flow of particulate using a studded roller feeder. Journal of Agricultural Engineering Research, 1994; 59(4): 221-230.

Turan J J, Findura P J, Djalovic I G, Sedlar A D, Bugarin R M, Janic T V. Influence of moisture content on the angle of repose of nitrogen fertilizers. International Agrophysics, 2011; 25(2): 201-204.

De D. Flow behaviour of chemical fertilizers as affected by their properties. Journal of Agricultural Engineering Research, 1989; 42(4): 235-249.

Nukeshev S, Eskhozhin D, Lichman G, Karaivanov D, Zolotuhin E, Syzdykov D. Theoretical substantiation of the design of a seeding device for differentiated intra soil application of mineral fertilizers. Acta Universitatis Agriculturae et Silviculturae Mendelianae Brunensis, 2016; 64(1): 115-122.

Yazgi A. Effect of seed tubes on corn planter performance. Applied Engineering in Agriculture, 2016; 32: 783-790.

Lei X L, Hu H J, Wu W C, Liu H N, Liu L Y, Yang W H. Seed motion characteristics and seeding performance of a centralised seed metering system for rapeseed investigated by DEM simulation and bench testing. Biosystems Engineering, 2021; 203: 22-33.

Nukeshev S, Eskhozhin D, Karaivanov D, Yeskhozhin K. Determination of parameters of the main distributor for fertilizer applying machine. Bulgarian Journal of Agricultural Science, 2014; 20: 1513-1521.

Xi X B, Gu C J, Shi Y J, Zhao Y, Zhang Y F, Zhang Q. Design and experiment of no-tube seeder for wheat sowing. Soil and Tillage Research, 2020; 204: 104724. doi: 10.1016/j.still.2020.104724.

Kocher M, Coleman J, Smith J, Kachman S. Corn seed spacing uniformity as affected by seed tube condition. Applied Engineering in Agriculture, 2011; 27(2): 177-183.

Yuan J, Liu Q, Liu X, Zhang T, Zhang X. Granular multi-flows fertilization process simulation and tube structure optimization in nutrient proportion of variable rate fertilization. Transactions of the CSAM, 2014; 45: 81-87. (in Chinese)

Lei X L, Liao Y T, Zhang Q S, Wang L, Liao Q X. Numerical simulation of seed motion characteristics of distribution head for rapeseed and wheat. Computers and Electronics in Agriculture, 2018; 150(10): 98-109.

Endrerud H C. Influence of tube configuration on seed delivery to a coulter. Journal of Agricultural Engineering Research, 1999; 74(2): 177-184.

Alekseev E, Maksimov I, Terentev G, Maksimov E. Seed distribution by the coulter for the subsoil broadcast seeding. Journal of Physics: Conference Series, 2020; 1515: 042040. doi: 10.1088/1742-6596/1515/4/042040.

Lain S, Sommerfeld M. Particle transport in turbulent flows along horizontal ducts. Latin American Applied Research, 2011; 41(5): 301-304.

Jafari M, Hemmat A, Sadeghi M. Comparison of coefficient of variation with non-uniformity coefficient in evaluation of grain drills. Journal of Agricultural Science and Technology, 2011; 13(5): 643-654.

Kim Y J, Kim H J, Ryu K H, Rhee J Y. Fertiliser application performance of a variable-rate pneumatic granular applicator for rice production. Biosystems Engineering, 2008; 100(4): 498-510.

Guler I E. Effects of flute diameter, fluted roll length, and speed on alfalfa seed flow. Applied Engineering in Agriculture, 2005; 21(1): 5-7.

Cundall P A, Strack O D. A discrete numerical model for granular assemblies. Geotech, 1979; 29(1): 47-65.

Li X Y, Du Y X, Liu L, Mao E R, Yang F, Wu J, et al. Research on the constitutive model of low-damage corn threshing based on DEM. Computers and Electronics in Agriculture, 2022; 194: 106722. doi: 10.1016/j.compag.2022.106722.

Adilet S, Zhao J, Sayakhat N, Chen J, Nikolay Z, Bu L X, et al. Calibration strategy to determine the interaction properties of fertilizer particles using two laboratory tests and DEM. Agriculture, 2021; 11(7): 592. doi: 10.3390/agriculture11070592.

Sugirbay A, Hu G R, Chen J, Mustafin Z, Muratkhan M, Iskakov R, et al. A study on the calibration of wheat seed interaction properties based on the discrete element method. Agriculture, 2022; 12(9): 1497.

Horabik J, Wiącek J, Parafiniuk P, Bańda M, Kobylka R, Stasiak M, et al. Calibration of discrete-element-method model parameters of bulk wheat for storage. Biosystems Engineering, 2020; 200(16): 298-314.

Marigo M, Stitt E H. Discrete element method (DEM) for industrial applications: comments on calibration and validation for the modelling of cylindrical pellets. KONA Powder and Particle Journal, 2015; 32(2): 236-252.

Moysey P A, Thompson M R. Determining the collision properties of semi-crystalline and amorphous thermoplastics for DEM simulations of solids transport in an extruder. Chemical Engineering Science, 2007; 62(14): 3699-3709.




Copyright (c) 2023 International Journal of Agricultural and Biological Engineering

Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 International License.

2023-2026 Copyright IJABE Editing and Publishing Office