Experimental study on the key factors of low-loss threshing of high-moisture maize

Xiaolong Zhu, Ruijuan Chi, Yuefeng Du, Jiahao Qin, Zexin Xiong, Weitong Zhang, Xiaoyu Li

Abstract


The rates of maize breakage and entrainment loss are high in the harvest of high-moisture maize, which remains an issue with the development of agricultural mechanization. In order to reduce the maize breakage and entrainment loss rates, the correlations among key factors, such as the threshing cylinder speed, concave clearance and feeding rate, and the rates of breakage and entrainment loss during high-moisture maize harvesting were studied in this paper. A single-factor experiment was carried out using a single-longitudinal-axial flow maize harvester, and an orthogonal experiment was carried out using single- and double-longitudinal-axial flow maize harvesters with the Taguchi experimental design method. The single-factor experiment revealed that when the cylinder speed increased, the breakage rate of maize decreased first and then increased, while the entrainment loss rate decreased. The breakage rate of maize decreased as the concave clearance increased, while the entrainment loss rate decreased first and then increased. The optimum value of the concave clearance was positively correlated with the ear diameter of maize; Additionally, the minimum breakage rate of maize occurred when the feeding rate was at the rated value, and the entrainment loss rate increased as the feeding rate increased. The orthogonal experiments revealed that the importance of cylinder speed, feeding rate, concave clearance on the maize breakage and entrainment loss rates were in descending order. The optimum values of parameters for the single-longitudinal-axial flow maize harvester were 370 r/min cylinder speed, 40 mm concave clearance and 10 kg/s feeding rate. The optimum values of parameters the double-longitudinal-axial flow maize harvester were 550 r/min cylinder speed, 35 mm concave clearance and 10 kg/s feeding rate. The research can provide a reference for parameter configuration and control strategy for the longitudinal-axial flow maize harvester with high-moisture maize.
Keywords: high-moisture maize, maize harvester, parameter configuration, Taguchi experiment
DOI: 10.25165/j.ijabe.20201305.5653

Citation: Zhu X L, Chi R J, Du Y F, Qin J H, Xiong Z X, Zhang W T, et al. Experimental study on the key factors of low-loss threshing of high-moisture maize. Int J Agric & Biol Eng, 2020; 13(5): 23–31.

Keywords


high-moisture maize, maize harvester, parameter configuration, Taguchi experiment

Full Text:

PDF

References


Li S S. Study on the methods of layout optimization design and virtual verification of self-propelled corn harvester. PhD dissertation. Beijing: China Agricultural University, 2016; 139p. (in Chinese)

National Bureau of Statistics of China. Announcement of the national bureau of statistics on food production in 2017. National Bureau of Statistics of China, Department/Division, 2017. (in Chinese)

Geng A J, Yang J N, Zhang J, Zhang Z L, Yang Q Y, Li R X. Influence factor analysis of mechanical damage on corn ear picking. Transactions of the CSAE, 2016; 32(22): 56–62. (in Chinese)

Johnson P C, Clementson C L, Mathanker S K, Grift T E, Hansen A C. Cutting energy characteristics of Miscanthus x giganteus stems with varying oblique angle and cutting speed. Biosyst Eng, 2012; 112(1): 42–48.

Shinners K J, Boettcher G C, Hoffman D S, Munk J T, Muck R E, Weimer P J. Single-pass harvest of corn grain and stover: performance of three harvester configurations. Transactions of the ASABE, 2009; 52(1): 51–60.

Wang J, Li Y, Ma Z, Hu B, Yu S. Structural characteristics and development trend of key equipment of corn harvesting machinery. Journal of Agricultural Mechanization Research, 2019; 41(9): 1–8. (in Chinese)

Yang L, Cui T, Qu Z, Li K, Yin X, Han D, et al. Development and application of mechanized maize harvesters. Int J Agric & Biol Eng, 2016; 9(3): 15–28.

Colbert T B. Iowa farmers and mechanical corn pickers, 1900-1952. Agricultural History, 2000; 74(2):530–544.

Mahmoud A R, Buchele W F. Corn ear orientation effects on mechanical damage and forces on concave. Transactions of the ASAE, 1975; 18(3): 444–447.

Wacker P. Maize grain damage during harvest. Landtechnik, 2005; 60(2): 84–85.

Irudayaraj J, Haghighi K, Stroshine R L. Finite element analysis of drying with application to cereal grains. Journal of Agricultural Engineering Research, 1992; 53(3): 209–229.

Irudayaraj J, Haghighi K, Stroshine R. Stress analysis of viscoelastic materials during drying. II. Application to grain kernels. Dry Technol, 1993; 11(5): 929–959.

Srivastava A K, Herum F L, Stevens K K. Impact parameters related to physical damage to corn kernel. Transactions of the ASAE, 1976; 19(6): 1147–1151.

Huang H, Faulkner D B, Berger L L, Eckhoff S R. Harvest date influence on dry matter yield and moisture of Corn and stove. Transactions of the ASABE, 2012; 55(2): 593–598.

Chai Z W, Wang K R, Guo Y Q, Xie R Z, Li L L, Ming B, et al. Current status of maize mechanical grain harvesting and its relationship with grain moisture content. Scientia Agricultura Sinica, 2017; 50(11): 2036–2043.

Lei X P. Studies on the feasibility of maize mechanically harvesting grain in Huanghuaihai Regions. Master dissertation. Baoding: Hebei Agriculture University, 2015; 45p. (in Chinese)

Liu J Y, Cui Z K, Ma J C, Jiao W. Problems and countermeasures of wheat corn rotation production mechanization for main crops in Huanghuaihai Region. Journal of Agricultural Mechanization Research, 2016; 38(5): 259–263. (in Chinese)

Gao L X, Li F, Zhang X W, Zhang Y L, Liu X, Jiao W P. Mechanism of moisture content affect on corn seed threshing. Transactions of the CSAM, 2011; 42(12): 92–96. (in Chinese)

Yi K C, Zhu D W, Zhang X W, Yao Z H, Liu Z. Effect of moisture content on corn grain harvesting mechanization. Chinese Agricultural Mechanization, 2016; 37(11): 78–80. (in Chinese)

Qu H J, Zhang D L, Yang T W, Xu Z D. Experimental research on corn threshing performance effected by moisture content. Journal of Agricultural Mechanization Research, 2014; 36(2): 153–156. (in Chinese)

Zhou X. Research the damage mechanism of seed corn and thresing technology with lower damage. Master dissertation. Shenyang: Shenyang Agricultural University, 2006; 7p. (in Chinese)

Petkevichius S, Shpokas L, Kutzbach H D. Investigation of the maize ear threshing process. Biosyst Eng, 2008; 99(4): 532–539.

Xu L Z, Li Y M, Ding L F. Contacting mechanics analysis during impact process between rice and threshing component. Transactions of the CSAE, 2008; 24(6): 146–149. (in Chinese)

Xu L Z, Li Y M, Ma C X, Li H C. Design and experiment of threshing and separating unit with double axial cylinder. Transactions of the CSAM, 2009; 40(11): 55–58. (in Chinese)

Qu Z, Zhang D X, Yang L, Zhang T L, Wang Z D, Cui T. Experiment on feed rate and cylinder speed of longitudinal axial flow threshing and separating device for maize. Transactions of the CSAM, 2018; 49(2): 58–65. (in Chinese)

Chinese Academy of Agricultural Mechanization Sciences. Agricultural machinery design manual. China Agricultural Science and Technology Press, 2007; 1885p. (in Chinese)

Di Z F, Cui Z K, Zhang H, Zhou J, Zhang M Y, Bu L X. Design and experiment of rasp bar and nail tooth combined axial flow corn threshing cylinder. Transactions of the CSAE, 2018; 34(1): 28–34. (in Chinese)

Li X P, Gao L X. Performance test on corn thresher with different-speed threshing parts. Transactions of the CSAE, 2009; 25(12): 102–106. (in Chinese)

Keller D L, Converse H H, Hodges T O, Chung D S. Corn kernel damage due to high velocity impact. Transactions of the ASAE, 1972; 15(2): 330–332.

Standardization Administration of the People's Republic of China. Test Methods for Combine Harvester. GB/T21961-2008, 2008; 13p. (in Chinese)

Standardization Administration of the People's Republic of China. Measuring methods for agricultural machinery testing conditions-General rules. GB/T5262-2008, 2008; 11p. (in Chinese)

Standardization Administration of the People's Republic of China. Thresher-Testing method. GB/T5982-2017, 2017; 16p. (in Chinese)

Support M. What is the signal-to-noise ratio in a Taguchi design? https://support.minitab.com/en-us/minitab/18/help-and-how-to/modeling-statistics/doe/supporting-topics/taguchi-designs/what-is-the-signal-to-noise-ratio/. Accessed on [2019-08-25].




Copyright (c) 2020 International Journal of Agricultural and Biological Engineering

Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 International License.

2023-2026 Copyright IJABE Editing and Publishing Office