Design and performance test of a combined and adjustable precise rice seed metering device

Hongmei Xu, Wanru Liu, Hao Liu, Zhangfen Liu, Guozhong Zhang

Abstract


In order to address the issues of narrow seeding adjustment range and low accuracy of grain placement in the existing rice seeders, a mechanically and pneumatically adjustable precision hole-type seeder is designed. It is primarily composed of a seeding disk, air chamber, seed box, and seed discharge device. The design incorporates a symmetrical structure with dual disks and dual casings, enabling both single-sided and double-sided single-row and synchronized seeding. Based on theoretical analysis of seed charging, seed protection, and seed release, the following parameters were determined: seeding disk diameter of 192 mm, suction hole diameter of 1.48-1.52 mm, suction hole spacing of 3.04-9.41 mm, type hole distribution circle radius of about 62.1-77.0 mm, type hole diameter of 9 mm, stirrer plate length of 4.705-9.410 mm, and stirrer plate inclination angle of 0°-30°. Using a coupled simulation method of EDEM-Fluent, the impact of different type hole distributions, stirrer plate lengths, and inclination angles on seeding performance was analyzed. The results indicate that the main and secondary influencing factors on seed charging qualification rate are type hole diameter, stirrer plate inclination angle, and stirrer plate length. The optimal performance is achieved with a type hole diameter of 6 mm, stirrer plate length of 5 mm, and stirrer plate inclination angle of 10°, resulting in a seed charging qualification rate of 71.42%. Furthermore, Fluent software was utilized to analyze the influence of different suction hole spacings, diameters, and air chamber radii on seeding performance. The results revealed that the suction of rice seeds by the hole can be better realized with a suction hole spacing of 6 mm, a suction hole diameter of 1.5 mm, and an air chamber radius of 62 mm, at which the average negative pressure in the suction hole center was about 2824.56 Pa. A bench test and a field test were further performed on the device. The results showed that increasing the number of type holes and suction holes can contribute to more stable regulation of the seeding amount. The optimal single-sided seed metering could achieve a maximum qualified rate of 82.5%, a missing rate of 12.5%, and a repeating rate of 5%; while the optimal double-sided seed metering could obtain a maximum qualified rate, missing rate, and repeating rate of 72.5%, 15%, and 12.5%, respectively. This adjustable precision seeder can meet the requirements of precision sowing of Huanghuazhan rice varieties, and the research findings can provide reference for the structural optimization of precision rice seeders.
Keywords: rice, combined seed metering device, adjustable seeding amount, EDEM-Fluent
DOI: 10.25165/j.ijabe.20251801.8193

Citation: Xu H M, Liu W R, Liu H, Liu Z F, Zhang G Z. Design and performance test of a combined and adjustable precise rice seed metering device. Int J Agric & Biol Eng, 2025; 18(1): 101–114.

Keywords


rice, combined seed metering device, adjustable seeding amount, EDEM-Fluent

Full Text:

PDF

References


Luo X W, Jiang E C, Wang Z M, Tang X R, Li J H, Chen W T. Precision rice hill-drop drilling machine. Transactions of the CSAE, 2008; 24(12): 52–56. (in Chinese)

Liu W R, Zhang G Z, Zhou Y, Xu H M, Wu Q, Fu J W, et al. Application and development of intelligent technology in full mechanization of rice production. Journal of Huazhong Agricultural University, 2022; 41(1): 105–122. (in Chinese)

Xing H, Wang Z M, Luo X W, He S Y, Zang Y. Mechanism modeling and experimental analysis of seed throwing with rice pneumatic seed metering device with adjustable seeding rate. Computers and Electronics in Agriculture, 2020; 178: 105697.

Liu C B, Zang Y, Luo X W, Zeng S, Wang Z M, Yang W W, et al. Design and experiment of spiral grooved wheel for rice direct seeding machine. Journal of Shenyang Agricultural University, 2016; 47(6): 734739. (in Chinese)

Li Z W, Shao Y J. Study and test of electromagnetic vibrating type rice seeder for hill seedling nursery box. Transactions of the CSAM, 2000; 31(5): 32–34. (in Chinese)

Zhang M H, Luo X W, Wang Z M, Dai Y Z, Wang B L, Zheng L. Design and experiment of combined hole-type metering device of rice hill-drop drilling machine. Transactions of the CSAM, 2016; 47(9): 29–36. (in Chinese)

Zhang G Z, Zhang S S, Yang W P, Lu K, Lei Z Q, Yang M. Design and experiment of double cavity side-filled precision hole seed metering device for rice. Transactions of the CSAE, 2016; 32(8): 9–17. (in Chinese)

Xing H, Wang Z M, Luo X W, Zang Y, He S Y, Xu P, et al. Design and experimental analysis of rice pneumatic seeder with adjustable seeding rate. Int J Agric & Biol Eng, 2021; 14(4): 113–122.

Zhang M H, Wang Z M, Luo X W, Jiang E C, Dai Y Z, Xing H, et al. Effect of double seed-filling chamber structure of combined type-hole metering device on filling properties. Transactions of the CSAE, 2018; 34(12): 8–15. (in Chinese)

Ye Q. Design and experiment of a mechanical rice precision metering device with double cavity stirring hole. Master dissertation. Hubei: Huazhong Agricultural University, 2018. (in Chinese) doi: 10.7666/d.D01604001.

Xu J, Sun S L, He Z K, Wang X M, Zeng Z H, Li J, et al. Design and optimisation of seed-metering plate of air-suction vegetable seed-metering device based on DEM-CFD. Biosystems Engineering, 2023; 230: 277–300.

Zhao J L, Zhang C L, Wei Y P, Guo M Z, Chen C, Zhang C Q, et al. Design and testing of planting unit for rice dry-direct-seeding planter in cold region. Int J Agric & Biol Eng, 2023; 16(4): 76–84.

Zhang G Z, Luo X W, Zang Y, Wang Z M, Zeng S, Zhou Z Y. Experiment of sucking precision of sucking plate with group holes on rice pneumatic metering device. Transactions of the CSAE, 2013; 29(6): 13–20. (in Chinese)

Zhang M H, Xiao M, Ou Y L, Jiang E C, Qiao J, Wang Z M, et al. Optimization design and test of seed protecting structure of combined type-hole metering device. Journal of South China Agricultural University, 2021; 42(4): 99–105. (in Chinese)

Tang H, Guan T Y, Xu F D, Xu C S, Wang J W. Test on adsorption posture and seeding performance of the high-speed precision dual-chamber maize metering device based on the seed characteristics. Computers and Electronics in Agriculture, 2024; 216: 108471.

Du X, Liu C L. Design and testing of the filling-plate of inner-filling positive pressure high-speed seed-metering device for maize. Biosystems Engineering, 2023; 228: 1–17.

Binelo M O, De Lima R F, Khatchatourian O A, Stránský J. Modelling of the drag force of agricultural seeds applied to the discrete element method. Biosystem Engineering, 2019; 178: 168–175.

Tang H, Xu F D, Guan T Y, Xu C S, Wang J W. Design and test of a pneumatic type of high-speed maize precision seed metering device. Computers and Electronics in Agriculture, 2023; 211: 107997.

Gao X J, Xie G F, Li J, Shi G S, Lai Q H, Huang Y X. Design and validation of a centrifugal variable-diameter pneumatic high-speed precision seed-metering device for maize. Biosystems Engineering, 2023; 227: 161–181.

Zhang R F, Jiao W, Zhou J L, Qi B, Liu H, Xia Q Q. Parameter calibration and experiment of rice seeds discrete element model with different filling particle radius. Transactions of the CSAM, 2020; 51(S1): 227–235. (in Chinese)

Shi S, Zhang D X, Yang L, Cui T, Li K H, Yin X W. Simulation and verification of seed-filling performance of pneumatic combined holes maize precision seed-metering device based on EDEM. Transactions of the CSAE, 2015; 31(3): 62–69. (in Chinese)

Zhang G Z, Zang Y, Luo X W, Wang Z M, Li Z D. Line-churning tooth design and metering accuracy experiment of rice pneumatic precision hill-drop seed metering device on pregnant Japonica rice seed. Transactions of the CSAE, 2014; 30(17): 1–9. (in Chinese)

Shen H, Zhang J J, Chen X H, Dong J X, Huang Y X, Shi J T. Development of a guiding-groove precision metering device for high-speed planting of soybean. Transactions of the ASABE, 2021; 64(3): 1113–1122.

Li X L. Research on rice seed discharging device combined with spoon seed taking and piston hole insertion. Masterdissertation. Heilongjiang: Northeast Agricultural University, 2018. (in Chinese) doi: 10.7666/d.Y3430813.

Zhai J B, Xia J F, Zhou Y. Design and experiment of pneumatic precision hill-drop drilling seed metering device for hybrid rice. Transactions of the CSAM, 2016; 47(1): 75–82. (in Chinese)

Xue P, Xia X Y, Gao P Y, Ren D, Hao Y J, Hu B, et al. Double-setting seed-metering device for precision planting of soybean in high speed. Transactions of the ASABE, 2019; 62(1): 1–10.

Yang W P. Research on the seed metering quality detection system of rice precision hole seeding metering device based on Labview. Master dissertation. Hubei: Huazhong Agricultural University, 2018. (in Chinese) doi: 10.7666/d.D01155272.

Zhou Y, Hu M J, Xia J F, Zhang G Z, Xu Z Y, Feng C C, et al. Design and experiment of inside-filling adjustable precision seed-metering device with combined hole for cotton. Transactions of the CSAE, 2018; 34(18): 59–67. (in Chinese)




Copyright (c) 2025 International Journal of Agricultural and Biological Engineering

Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 International License.

2023-2026 Copyright IJABE Editing and Publishing Office