Design of multi-section luffing apple pruning equipment and cutting test of the key components

Siyuan Tong, Wenbin Li, Yaxiong Wang, Lei Zhang, Feng Kang

Abstract


In order to reduce the labor intensity and improve the efficiency of pruning, this study designed a multi-section luffing apple pruning equipment suitable for apple orchards in hilly and mountainous areas of China. In the essay, the structure and working principle of the equipment are expounded, the cutter was analyzed, and the parameters were determined. Using the self-made test bench to simulate the field experiment, this study selected the ratio of cutting speed to feeding speed and feeding speed as the influencing factors and took the cut-off rate, cutting efficiency and cutting power as the objectives to carry out single factor experiment and quadratic regression orthogonal experiment. The test results show that the cutting power increases with the increase of ratio of cutting speed to feeding speed, and the cut-off rate and cutting efficiency first increase and then decrease. As the feeding speed increases, the cutting efficiency and power increase, and the cut-off rate decreases. When the cut-off rate was greater than 80%, the optimal combination of operating parameters was the feeding speed of 0.55 m/s and ratio of cutting speed to feeding speed of 1.29. Under this combination, the cut-off rate was 84.9%, the cutting efficiency was 13.1, and the cutting power was 175.7 W. The error between the predicted target value of the model and the average measured target value was less than 7%, so the test results are reliable. According to the obtained optimal operating parameters, the actual cutting experiment of the pruning equipment in the field was carried out, and the cutting rate was 96.3%, which meet the design requirements. This study can also meet the needs of mechanized pruning of fruit trees with different crown shapes, improve the applicability of pruning equipment, and provide support for the development of mechanized pruning equipment in China.
Keywords: apple, pruning equipment, cutting test, optimal parameters, regression analysis
DOI: 10.25165/j.ijabe.20241701.7988

Citation: Tong S Y, Li W B, Wang Y X, Zhang L, Kang F. Design of multi-section luffing apple pruning equipment and cutting test of the key components. Int J Agric & Biol Eng, 2024; 17(1): 109-117.

Keywords


apple, pruning equipment, cutting test, optimal parameters, regression analysis

Full Text:

PDF

References


National Bureau of Statistics. China Statistical Yearbook. Beijing: China Statistics Press, 2021

Huang C W, Cai D X, Wang W Z, Li J, Duan J L, Yang Z. Development of an automatic control system for a hydraulic pruning robot. Computers and Electronics in Agriculture, 2023; 214: 108329.

Li S G, Kang F, Li W B, Zhou S Z, Han X M. Progress advance on pruning mechanization and automation of fruit trees. Journal of Northeast Agricultural University, 2017; 48（8）: 88–96. （in Chinese）

Gai Q G, Zhu X, Shi Q H. The impact of labor migration on agricultural production in China. China Economic, 2014; 13（3）: 1147–1170. （in Chinese）

He L, Schupp J. Sensing and automation in pruning of apple trees: A review. Agronomy, 2018; 8（10）: 211.

Ma B K, Xu J Z, Sun J S. Consideration for high density planting with dwarf rootstocks in apple in China. Journal of Fruit Science, 2010; 27（1）: 105–109. （in Chinese）

Zahid A, Mahmud M S, He L, Heinemann P, Choi D, Schupp J. Technological advancements towards developing a robotic pruner for apple trees: A review. Computers and Electronics in Agriculture, 2021; 189: 106383.

Dorigoni A. Cutting equipment for plant rows. United States Patent, US9295199B2.

Spagnolo F. Rotary blade pruning machine. United States Patent, US6250056B1.

Spagnolo F. SG pruning machine. Australian Patent, AU2006100356A4.

Spencer A. Tree trimming and pruning machine. United States Patent, US00543999A.

Chen K, Li H, Nasihati, Wang M B. Development of 3PJ-1 type gantry pruning machine for grapes. Journal of Chinese Agricultural Mechanization, 2017; 38（2）: 28–33. （in Chinese）

Zhang J X, Huang T, Wang M B. Design and experiment of single motor reciprocating grape pruning machine. Transactions of the CSAM, 2021; 52（8）: 106–116. （in Chinese）

Long K. Design and experimental research on reciprocating vines pruning machine. Master dissertation. Urumqi: Xinjiang Agricultural University, 2014; 68p. （in Chinese）

Zhang D X, Min L Q, Li Q J, Liu X F, Ren D M, Zhang C Y, et al. Design of PJS-1 two-wing grape pruning machine. Agricultural Equipment and Vehicle Engineering, 2016; 54（2）: 77–81. （in Chinese）

Han H M, Zhou Y, Jia S X, Cai W L, Wen X Y. Design of summer wine grape pruning machine. Journal of Agricultural Mechanization Research, 2020; 42（9）: 81–86, 92. （in Chinese）

Chang J X, Zhang Y L, Li S J, Zhang W, Ma P Y. Design of citrus trimmer with bilateral and neat trim. Journal of Huazhong Agricultural College, 2019; 38（3）: 104–111. （in Chinese）

Liu X C, Liu X F, Zhang L F, Min L Q, Chu Y H, Ren D M. Design and research of wide band combination copying prune machine for new orchard. Journal of Chinese Agricultural Mechanization, 2020; 41（8）: 65–71. （in Chinese）

Wu K, Song Y P. Research progress analysis of crop stalk cutting theory and method. Transactions of the CSAM, 2022; 53（6）: 1–20. （in Chinese）

McRandal D M, McNulty P B. Impact cutting behaviour of forage crops I. Mathematical models and laboratory tests. Journal of Agricultural Engineering Research, 1978; 23（3）: 313–328.

Liu J, Zhao D, Zhao J. Study of the cutting mechanism of oil tree peony stem. Forests, 2020; 11（7）: 760.

Chen Y, Gratton J L, Liu J. Power requirements of hemp cutting and conditioning. Biosystems Engineering, 2004; 87（4）: 417–424.

Igathinathane C, Womac A R, Sokhansanj S. Corn stalk orientation effect on mechanical cutting. Biosystems Engineering, 2010; 107（2）: 97–106.

Igathinathane C, Pordesimo L O, Schilling M W, Columbus E P. Fast and simple measurement of cutting energy requirement of plant stalk and prediction model development. Industrial Crops & Products, 2011; 33（2）: 518–523.

Tian K P, Li X W, Zhang B, Chen Q M, Shen C, Huang J C. Design and test research on cutting blade of corn harvester based on bionic principle. Applied Bionics and Biomechanics, 2017; 2017: 6953786.

Du V, Quoc H N, Nguyen H C. Multi-objective optimisation of cutting force and cutting power in chopping agricultural residues. Biosystems Engineering, 2020; 191: 107–115.

Azadbakht M, Esmaeilzadeh E, Esmaeili-Shayan M. Energy consumption during impact cutting of canola stalk as a function of moisture content and cutting height. Journal of the Saudi Society of Agricultural Sciences, 2015; 14（2）: 147–152.

Gao Y, Kang F, Kan J, Wang Y, Tong S. Analysis and experiment of cutting mechanical parameters for Caragana korshinskii （C. K.） Branches. Forests, 2021; 12: 1359.

Johnson P C, Clementson C L, Mathanker S K, Grift T E, Hansen A C. Cutting energy characteristics of Miscanthus x giganteus stems with varying oblique angle and cutting speed. Biosystems Engineering, 2012; 112（1）: 42–48.

Mathanker S K, Grift T E, Hansen A C. Effect of blade oblique angle and cutting speed on cutting energy for energycane stems. Biosystems Engineering, 2015; 133: 64–70.

Allameh, Alireza, Reza, Alizadeh, Mohammad. Specific cutting energy variations under different rice stem cultivars and blade parameters. Idesia （Arica）, 2016; 34（5）: 11–17.

Hou J, Bai J, Yao E, Zhu H. Design and parameter optimization of disc type cutting device for castor stem. IEEE Access, 2020; 8: 191152–191162.

Ghahraei O, Ahmad D, Khalina A, Suryanto H, Othman J. Cutting tests of kenaf stems. Transactions of the ASABE, 2011; 54: 51–56.

Huang J C, Zhang B, Tian K P, Liu H L. Design and optimization of the parameters of the key components for reed harvester. International Journal of Agricultural and Biological Engineering, 2022; 15（6）: 96–103.

Feng Y L, Yin X C, Jin H R, Tong W Y, Ning X F. Design and experiment of a Chinese chive harvester. Int J Agric & Biol Eng, 2023; 16（2）: 125–131.

Kang F, Tong S Y, Zhang H S, Li W B, Chen Z J, Zheng Y J. Analysis and experiments of reciprocating cutting parameters for apple tree branches. Transactions of the CSAE, 2020; 36（16）: 9–16. （in Chinese）

Xia J H, Li B Z, Zhang L S. Shaping and pruning technology of high spindle apple tree. Deciduous Fruits, 2013; 45（1）: 56–57. （in Chinese）

Zhang D X, Qin X T, Liu X F, Li Q J, Min L Q, Ren D M. Research progress and supporting equipment of orchard branch pruning at home and abroad. China Fruits, 2021; 2: 6–12. （in Chinese）

GB/T10940-2008. Reciprocating mower. China standard, 2008. （in Chinese）




Copyright (c) 2024 International Journal of Agricultural and Biological Engineering

Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 International License.

2023-2026 Copyright IJABE Editing and Publishing Office